Is My Gas Fireplace Valve On Or Off?

Gas fireplaces are increasingly common, especially with winters becoming colder and more intense. It’s a great idea to have a gas stove, but you need to know how it works! 

A key thing to know is how to tell if your gas fireplace’s valve is on or off. The gas valve is open when the handle’s long side is parallel to the gas line. The gas valve is turned off when it is turned only a quarter of the way and is perpendicular to the incoming gas pipe. 

There’s still a lot more about gas stoves that need to be discussed. So keep on reading below to find out more! 

Do Gas Fireplaces need a Shut-off Valve?

Gas fireplaces require a shut-off valve. These are required by law. The shut-off valve must also be located outside of the firebox. 

The law goes further, stating that each appliance is required to have a shut-off valve separate from the appliance. This shut-off valve has to be in the same room as the appliance.

It can be no further than six feet from the appliance. Finally, it must also be installed “upstream” from the device it serves, whether a union, connector, or quick disconnect. 

How does a Gas Fireplace Valve Work?

Gas fireplaces use a thermocouple to monitor the flame. They also use a thermopile to enable control via a thermostat or any other remote device. The thermocouple is used to sense the pilot flame while preventing flow to the stove’s main burners when there is inadequate heat to ignite it. 

Thermocouples are passive sensors. These sensors generate an electrical current when a thermal gradient can interact with an exposed open circuit. First, the sensor senses this heat from the pilot flame. The thermocouple then induces an electrical charge, which affects an electromagnet inside the gas valve that allows gas flow to the stove’s main burners. 

Gas fireplaces usually fail due to the pilot light igniting but not being able to stay lit. If this occurs, it means there is an issue with the thermocouple. Additionally, a loose connection or natural corrosion can cause a thermocouple to fail. However, the most common problem is that the junction is covered in soot and needs to be cleaned or replaced. 

Where is the Gas Valve for my Fireplace?

This control panel is located either behind the front screen. This is where a knob that controls the flow of gas can be turned on or off. Typically, the gas valve for a fireplace is found on the control panel. 

Other fireplaces have a round slot for controlling the gas valve. This is usually located near the fireplace. In this setup, the gas flow is controlled with a fireplace key. This key is also called a hex key.

Another way of controlling your gas valve is with an electronic wall switch. Most modern fireplaces come equipped with a wall switch control panel which is used to activate the fireplace. It will also adjust the height of the flames. 

How do you Tell if the Gas Valve is On or Off?

As previously stated, all gas fireplaces have a valve that controls the flow of the gas. To tell if it is on, check to see if the valve is either parallel or turned a quarter turn, so it is perpendicular. 

If the gas valve is parallel to the incoming gas line, it is on. If you want to stop the gas flow, turn the gas valve a quarter turn, perpendicular to the incoming gas line. In this position, the gas valve is off. 

To check and reset your gas valve: 

1. Ensure all gas appliances are turned off 

2. You should turn off the service valve for fifteen seconds 

3. Now, open the valve only one-sixth of a turn. Ensure you hear gas flowing through the pipes. 

4. When the flow stops, this means that the gas has pressurized the system. Now slowly fully open the service valve.

How do I Turn on my Gas Fireplace Valve?

If the gas valve is parallel to the incoming gas line, it is on. Turn the gas valve if it is not in this position. 

How do I Turn off my Gas Fireplace Valve?

If you want to stop the gas flow, turn the gas valve a quarter turn, perpendicular to the incoming gas line. In this position, the gas valve is off. 

Is a Faulty Gas Fireplace Valve Dangerous?

Yes, a faulty gas fireplace valve is dangerous. Gas is dangerous, so you should never repair a gas fireplace problem by yourself. This can be very dangerous. You should immediately call a professional and have them deal with the issue. 

If you’re having problems with your gas fireplace, first check to ensure the gas valve is on! If there is no ignition and no gas smell, the issue may be as simple as a closed gas valve. 

Here are a few signs that your gas fireplace may need some maintenance. First, if your pilot light refuses to stay lit, that’s a sign of a big issue. The cause of this can be a broken thermopile. A more severe cause of this issue is faulty wiring. 

The second sign of an issue is a rotten egg smell. If you smell this or hear a hissing sound, it means there is a gas leak. If you think there is a gas leak, stop what you are doing and leave your home. Do not attempt to fix the issue yourself. Instead, call a professional to deal with it. 

The third sign of issues with your gas fireplace is soot buildup. Too much soot means something is wrong. If there is too much soot, call a professional immediately. 

How do I know if my Gas Fireplace Valve is Bad?

If the pilot light of your gas stove stays on, yet the main burner fails to work, then there may be an issue with the thermopile. 

If your gas valve is turned on yet, no gas is flowing, that means there is a serious issue. 

You may be wondering, why do gas valves fail? They can fail due to a variety of issues. These include contamination, misuse, and simple product deficiency. 

How much does it Cost to Replace a Gas Fireplace Valve?

Replacing a gas valve can cost anywhere between $350 to $595. It depends on the issue, the price of the part(s) required, and the rates of the company you use. Never, ever attempt to fix a problem with your gas stove by yourself. It can be incredibly dangerous. Always leave it to the professionals. 

Wrapping It Up

Gas fireplaces are a great way to stay warm during the wintertime. All gas fireplaces require a shut-off valve. These are required by law to be in the same room and within six feet of the gas appliance. 

The gas valve is open when the handle’s long side is parallel to the gas line. The gas valve is turned off when it is turned only a quarter of the way and is perpendicular to the incoming gas pipe.

Overall, there’s a lot to do with gas fireplaces, but you will find it isn’t as difficult as you initially thought once you research it.