How To Turn On Heater In House

As the temperatures continue to drop, you may be wondering how to turn on your heater. Believe it or not, there is an art and science behind turning on a heater.

There are many different types of heaters so that it can be unclear! This article will talk about how you can turn your home into a warm, cozy place.

Can I Just Turn My Heat On?

It’s not advisable to flip the switch and have your heating system on after it has been dormant for six months or more throughout the year. Therefore, you should not turn the heater on and begin utilizing it again after months of inactivity.

When these devices are kept in damp or humid conditions, they break down and develop dust. Over time, this can lead to mechanical problems.

Suppose you allow dirty, moldy air into your heating system before it has a chance to dry out thoroughly. In that case, mold spores can develop and circulate throughout your home via the venting systems and give everyone allergies or respiratory issues.

You want clean, fresh air in your home, not dirty air that will make you and your family sick.

When Should Heater be Turned On?

The best time to turn on your heater is when the temperature inside begins to drop below 65 degrees Fahrenheit. You should also consider turning on your heater if you are experiencing a cold draft in your home.

Heating your home can help improve your comfort and indoor air quality.

You should turn off your heater when you are no longer home or if the inside temperature of your house reaches 80 degrees Fahrenheit.

You can also set your thermostat to automatically shut down for five hours each day while you’re sleeping. Doing so will help save money on heating bills and energy costs while keeping indoor air quality high.

Is It Better to Turn Your Heat off or Down?

It’s advisable to turn it down to save money and conserve energy. However, if you turn it off, the pipes could freeze.

Many people ask themselves whether it’s better to turn their heat down or off when they leave for work in the winter months. In short, it depends on a few factors:

  • how well your home is insulated
  • the type of heating system you have, and
  • the weather conditions outside.

If your home isn’t very well insulated, it’s essential to keep your heat at a low temperature while you’re away so that the inside of your house doesn’t get too cold. Turning off your heat altogether can cause your pipes to freeze, and no one wants that!

If you have a heating system that runs on gas or oil, it’s best to turn it off completely when you’re not home. These systems generate heat even when they’re turned off, so turning them down won’t save you very much money.

But if you have a heating system that runs on electricity, it’s best to turn it down to the lowest setting when you’re not home. This will help keep your energy bills down without causing your pipes to freeze.

Of course, the best way to save on your energy bills is to insulate your home well. Call a professional if you’re not sure how to do that or need help fixing drafts in your house! They can help you keep your home warm and cozy all winter long.

Things to Do Before Turning Your Heater in Winter

Before you turn on your heater, there are several things to do. These include:

Changing the Filter

Changing your filter is one of the most important things you can do to ensure that your heater works well and continues to work for a long time.

Don’t forget: change it every month or so, depending on what type of filter you have.

Set the Thermostat to “Heat” Mode

Set it to “heat” mode if you have a programmable thermostat. This will ensure that your heater is on when you need it.

If you don’t have a programmable thermostat, set the thermostat at least two degrees higher than the room temperature.

This will help your heater to run more efficiently.

Clean the Burners

Cleaning the burners will help your heater run more efficiently. Some furnaces have burners that you can remove, making cleaning them much easier.

Check the Blower

The blower is responsible for distributing the heat around your house. Therefore, you should check it every year to ensure that it’s in good condition.

If it needs cleaning, oiling, or repairing, take care of it as soon as possible. A broken blower can cause your heater to work much harder and lead to an early failure.

Ensure the Heating Vents aren’t Blocked

Check the heating vents throughout your house before you turn on the heater. If a vent is blocked, it could prevent hot air from circulating properly and hamper how effective your heater will be at warming up that room.

This won’t only make your home less comfortable but also increase the risk of fire or carbon monoxide poisoning if a room isn’t heated properly.

Clean the Vents and Chimneys

Just as you should clean the burners, it’s also important to clean the vents and chimneys. This will help your heater run more efficiently and could prevent a fire from happening.

Use Safety Monitors

Using your carbon monoxide and smoke detectors is not a bad idea. This will ensure that you are alerted if there is an issue with the heater or needs repairs.

Stay Alert on Unusual Smells and Noises

If you smell something strange or hear a noise that’s not normal, it’s time to turn off your heater and call a professional. These could be signs that there is something wrong with your heater and it needs repairs.

Consider a Professional Tune-Up

Even if you’ve taken all of these precautions, it’s still a good idea to have a professional tune-up of your heater every year. This will ensure that everything is in working order and that there are no hidden problems.

It can also help increase the life of your heater and save you money in the long run.

How to Turn on Heater in House

If you have an electric heater in your home, there are a few simple steps to turning it on.

Step One: Locate the Starting Knob and Turn it On

The starting knob is usually located on the front or side of the heater. Turn it to the “on” position, and wait a minute for the heater to start up.

Step Two: Turn the Knob to “Pilot” Mode

After the heater starts, turn the knob to “pilot” mode. Follow by repeatedly pressing the “Ignite” button until the pilot light starts.

Step Three: Hold Down the Ignite Button for Five Seconds

Once the pilot light is on, you will need to hold down the button for about five seconds. The heater should then start up at full speed.

Step Four: Adjust the Temperature and Other Settings

Once the heater starts, you can adjust the temperature and other settings as needed.

How Does Gas Heater Work in a House?

A gas heater is a heat-producing device that works by burning natural gas or propane. The heat from the combustion is transferred to a metallic surface. The hot metal surface then transfers its heat to surrounding air, which in turn heats your home.

A gas heater works on many of the same principles as any other furnace or water heater: heating air and moving it throughout the house via ductwork. Because most gas heaters are also used as water heaters, they have two combustion chambers and a blower to move air.

How to Turn on Gas Heater in House

Now that you know how a gas heater works, it’s time to turn it on! The first step is locating your thermostat.

Step One

Locate the knob for turning on your gas heater and turn it to the “on” position.

Step Two

Turn the knob to “Pilot,” then press down the “Ignite” button. To light up the pilot light, if needed, repeatedly press the Ignite button.

Step Three

After the pilot light is lit, press the Ignite button for 10 to 15 seconds.

Step Four

Finally, set the gas heater’s temperature to match your desired level of warmth.

Enjoy the warmth! If you have any problems, don’t hesitate to contact a professional.

How Does Electric Heater Work in a House?

As the name suggests, electric heaters use electricity to produce heat. Electricity is passed through a resistor, creating heat that warms its air. This warm air is then circulated throughout the room by fans or ducts.

There are two types of electric heating systems: baseboard and convection. Baseboard heating systems involve installing metal panels along the walls of a room. These panels then heat up and radiate warmth into the room. Convection heating systems use fans to blow warm air around the room, heating the objects.

This type of heating is generally more efficient than baseboard heating, as it warms up the entire room rather than just the walls. However, it can be more expensive to install and maintain.

How to Turn on an Electric Heater in a House

There are two ways to turn on an electric heater in a house: a thermostat or a switch.

Thermostats are devices that regulate the temperature of a room. They usually have a dial or buttons to set the temperature you want. They then turn on or off the heater at that given temperature, allowing for greater precision over how warm your house is.

Switches are more straightforward. There are two types of switches: on/off and dimmer. An on/off switch turns a device ‘on’ when turned up and ‘off’ when turned down. A dimmer switch allows you to adjust the brightness of a light by turning a knob.

To turn on an electric heater in a house using a thermostat, find it and set it to the desired temperature. Then locate the heater switch and turn it on. The heater will automatically turn on and off to maintain the desired temperature.

To turn on an electric heater in a house using a switch, find the switch and turn it on. The heater will now turn on and stay on until you turn it off.

How to Turn on Heater in House Honeywell?

Honeywell Thermostats are great options for house heating systems because they are programmable. This means you can have the heater turned on before you get home, so it is warm when you arrive. It also has a vacation mode which will save energy while you’re away.

Other features include automatic updates, touchscreen displays, and compatibility with many heating systems. If your old thermostat is broken or outdated, investing in a new Honeywell Thermostat may benefit you.

So, how can you turn on the heater in a house using the Honeywell thermostat?

Set the Time and Date

The first step is to set the time and date. You can do this by pressing the “Menu” button on your thermostat. This will bring up a list of options, one of which should be “Date & Time.”

From there, you can use the arrow buttons to change the date and time. Once you have it set, you can press the “Menu” button again to return to your list of options.

Program the Honeywell Thermostat

After you have set the time and date, you will need to program your Honeywell thermostat. You can do this by pressing the “Menu” button again and selecting “Program Mode.”

From there, use the arrow buttons to scroll through the different menus until you find the one that says “Heating.” You can then use the number buttons to set your desired temperature.

When you’re finished, press the “Menu” button again to return to your list of options.

Now that your thermostat is programmed, it will turn on and off automatically at times you specified. You can also use the touchscreen display to change the settings or manually override them if necessary.

How to Fix a Heater That Won’t Turn On?

If your heater isn’t turning on, you will want to start by checking the following:

Is the Thermostat On?

First, you will want to check that the thermostat is on. If it’s not, then turn your dial-up and wait for a few minutes before checking back in to see if there has been any change.

The Gas Should be on?

Second, you will want to check that the gas is on. Turn your knob to the “on” position if it’s not. You may need to wait a few minutes for the gas to heat up before you can turn on your furnace.

Check the Position of Your Furnaces Power Switch

Third, check the position of your furnace’s power switch. It should be in the “on” position. If it is not, then flick the switch to turn it on.

Replace Damaged Air Filters

Fourth, if you have an air filter, it’s crucial to replace it every few months. You can usually find the filters near your furnace. If they are dirty or clogged, then your furnace will not be able to work correctly.

Ascertain the Ignition Sensor’s Condition

Finally, it would be best to ascertain the ignition sensor’s condition. For example, if your furnace won’t stay on or is challenging to turn on, the sensor may be an issue.


Now that you know how to turn on the heater in your house, you can stay warm and cozy all winter long. Ensure you follow these tips to the letter, and you will be warm in no time.